Sitting Frog Phone Grip

Regular price $12.00
Shipping calculated at checkout.

Grip Type

This adorable sitting frog phone grip will help you hold your phone more securely and can be used to wrap a cord around as well! This phone bracket or phone grip is made of plastic and soft PVC featuring a mechanism that can adjust to three different heights. Please see the How to Use and Care instructions below for more information.


- 2.25″ at its longest side.
- Sits 1/2" high when adhered to surface.
- Uses a plastic air grip to hold the soft PVC design.
- Choose between two types of grips (swappable or permanent).
- Swappable Air grip is adjustable to three heights.
- Adheres and forms a strong bond to most surfaces.
- Adhesive backing removes cleanly when rubbing alcohol is applied.
- Adhesive is very strong. Usage on a device case is highly recommended.
- Phone grip features original artwork by me.
- Photography props, device and backdrops not included.

There are two types of grips offered at the moment, Swappable or Permanent.

Swappable: These grips feature small tabs that allow you you swap out the phone grip's design. They also allow you to rotate the phone grip's design, and they have three levels of extension. These have more features but are not as durable as the permanent grips.

Permanent: These grips have two levels of extension and have a soft middle section that makes them more comfortable to hold. They do not rotate and you cannot swap out the design of the grip. These are more durable and comfortable to use but have fewer features.




This is an air grip style phone grip featuring a soft PVC design on top. It adheres to your phone using a strong adhesive pad located on the back of the grip.

IMPORTANT NOTE: Due to the strength of the adhesive, it is strongly recommended that you do not adhere this phone grip directly onto your device. Please only use this item on a case or other surface that is easily removable from your device.

To install this phone grip, peel back the protective sticker covering the adhesive pad and carefully place the grip, design side up, where you wish to install it. Place the grip, adhesive side down, on the location you wish to install it. Now apply some gentle pressure on the design of the grip to form a seal between the adhesive and the surface and you're done!

The air grip on this item has three states. Gently tug on the air grip to extend it. To retract the air grip, gently push down on the design side of the grip.

Please see the Cleaning and Care instructions for this item to keep it looking nice and to prevent degradation of the adhesive or soft PVC of the design.

To preserve the integrity of the materials for your phone grip and the adhesive, avoid leaving your phone grip in direct sunlight for more than hour. Please also take care to avoid allowing your phone grip to freeze, or sit in temperatures of over 100F for long periods of time.

Over time, the design side of your phone grip may show some slight discoloration from the surfaces that it comes in contact with. This is a natural occurrence, though one way to prevent it is by making sure it isn't placed on dusty or dirty surfaces. Most of the time, your phone grip can be cleaned, but make sure to remove the case your phone grip is installed on from your device before cleaning.

You can renew and clean your phone grip using a small amount of soap and water...
1. Before cleaning your phone grip, remove the case or surface, with the phone grip on it, from your device.
2. Fill a cup with dish soap or a gentle hand soap and water.
3. Soak a cotton swab or small cotton pad in the soap and water.
4. Gently rub the soapy swab or pad over the surface of the phone grip.
5. Pat your phone grip to dry with a clean towel.

Some stains or discoloration may require more than soapy water. If your phone grip is still dirty after a gentle cleaning, you may use a solution of 1 parts bleach to 3 parts water to clean it...
1. Before cleaning your phone grip, remove the case or surface, with the phone grip on it, from your device.
2. Fill a disposable cup with 1 parts bleach to 3 parts water.
3. Soak a cotton swab in the bleach and water mixture.
4. Gently rub the swab over the surface of the phone grip.
5. Allow your phone grip to air dry for at least 10 to 15 minutes.
It may take the bleach up to 48 hours to lift the stains off your phone grip.

If you wish to remove the phone grip, firmly grip the bottom of the grip and slowly peel it up. This may distort the shape of the grip, so please take care. Once peeled off, the adhesive pad may still remain on the surface of your case. To remove the rest of the adhesive, soak a pad or cotton swab in rubbing alcohol and slowly rub at the residue to lift the remaining adhesive off your case. You can re-use the phone grip if the base is still intact by purchasing a new adhesive pad that is a 1 1/4" circle.

Looking for More?

Shop Our Catalog

Check out our entire catalog of products for pins, needle minders, accessories, stationery and more.

Alum + Ink Catalog

Recently viewed